Typical Physical and Chemical Properties

 
Interstitial Free (IF)
 
 
 Typical Chemistries:CMnPSSiAlTiV
Maximums:.005.08-.25.02.01.04.02-.06.02-.095.009

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled40-4726 max44 min.230 min2.1 min32
Hot Rolled45-5035 max40 min.200 minNA48
Hot Dipped and Galvannealed40-4726 max44 min.230 min2.1 min38



 
 
Extra Deep Drawing Steel (EDDS) AKA: Ultra Low Carbon (ULC)
 
 TypicalChemistries:CMnPSSiAlTiCbV
Maximums:.03.25.02.01.02.02-.06.02-.07.02-.07.009

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled40-4726 max40 min.210 min2.1 min38
Hot Rolled45-5338 max36 min.190 minNA50
Hot Dipped and Galvannealed40-4529 max38 min.200 min1.9 min42




Deep Drawing Steel (DDS)

 Typical Chemistries:CMnPSSiAlTiCb
Maximums:.05.30.02.015.02.02-.07NANA

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled40-4725 max42 min.210 min1.8 min48
Hot Rolled47-5338 max38 min.190 minNA65
Hot Dipped and Galvannealed47-5330 max38 min.200 min1.5 min50




Drawing Steel (DS) AKA: Drawing Quality (DQ)

 Typical Chemistries:CMnPSSiAl
Maximums:.06.48.02.02.02.02-.07

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled40-4830 max40 min.200 min1.8 min<48
Hot Rolled49-5742 max36 min.180 minNA<68
Hot Dipped and Galvannealed42-4936 max38 min.180 minNA<55




Commercial Steel (CS) w/ 1008 chems AKA: Commercial Quality (CQ)

 Typical Chemistires:CMnPSSiAl
Maximums:.10.5.03.035.02.02-.07

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled40-5235 max36 min.1 min1.2 min<65
Hot Rolled52-6445 max26 min.1 minNA<75
Hot Dipped and Galvannealed45-4145 max34 min.1 min1.2 min<68




Commercial Steel w/ 1008/1010 chems AKA: Commercial Quality (CQ)

 Typical Chemistries:CMnPSSiAl
Maximums:.13.6.03.035.02.02-.07

 Typical Mechanical Properties:TensileYieldElongationn-Valuer-ValueRb
Cold Rolled44-5340 max36 min.150 min1.0 min<65
Hot Rolled50-5850 max32 min.100 minNA<80
Hot Dipped and Galvannealed47-5345 max36 min.100 minNA70




Bake Hard - BH

BH 180 MPa
 Typical Mechanical Properties:TensileYieldElongationn-Value
Cold Rolled32519638.9.210
EG32519638.9.210
EG Alloy32519638.9.210
Hot Dipped and Galvannealed30518539.3.210

BH 210 MPa
Typical Mechanical Properties:TensileYieldElongationn-Value
Cold Rolled34422337.8.200
EG34422337.8.200
EG Alloy34422337.8.200
Hot Dipped and Galvannealed35523034.2.190

BH 240 MPa
 Typical Mechanical Properites:TensileYieldElongationn-Value
EG37825634.7.190



 
 
 
Carbon Sheet Steel Compositions
(Chemical Composition Limits, %)
Steel Designation No. C Mn P max S max
1001 .01 max .35 max .030 .035
1002 .02 max .35 max .030 .035
1003 .04 max .35 max .030 .035
1004 .02 / .06 .35 max .030 .035
1005 .06 max .35 max .030 .035
1006A .02 / .08 .45 max .030 .035
1006 .08 max .45 max .030 .035
1007 .02 / .10 .50 max .030 .035
1008 .10 max .50 max .030 .035
1009 .15 max .60 max .030 .035
1010 .08 - .13 .30 - .60 .030 .035
1012 .10 - .15 .30 - .60 .030 .035
1015 .13 - .18 .30 - .60 .030 .035
1016 .13 - .18 .60 - .90 .030 .035
1017 .15 - .20 .30 - .60 .030 .035
1018 .15 - .20 .60 - .90 .030 .035
1019 .15 - .20 .70 - 1.00 .030 .035
1020 .18 - .23 .30 -.60 .030 .035
1021 .18 - .23 .60 - .90 .030 .035
1022 .18 - .23 .70 - 1.00 .030 .035
1023 .20 - .25 .30 - .60 .030 .035
1025 .22 - .28 .30 - .60 .030 .035
1026 .22 - .28 .60 - .90 .030 .035
1030 .28 - .34 .60 - .90 .030 .035
1033 .30 - .36 .70 - 1.00 .030 .035
1035 .32 - .38 .60 - .90 .030 .035
1037 .32 - .38 .70 - 1.00 .030 .035
1038 .35 - .42 .60 - .90 .030 .035
1039 .37 - .44 .70 - 1.00 .030 .035
1040 .37 - .44 .60 - .90 .030 .035
1042 .40 - .47 .60 - .90 .030 .035
1043 .40 - .47 .70 - 1.00 .030 .035
1045 .43 - .50 .60 - .90  .030 .035
1046 .43 - .50 .70 - 1.00 .030 .035
1049 .46 - .53 .60 - .90 .030 .035
1050 .48 - .55 .60 - .90 .030 .035
1055 .50 - .60 .60 - .90 .030 .035
1060 .55 - .65 .60 - .90 .030 .035
1064 .59 - .70 .50 - .80 .030 .035
1065 .60 - .70 .60 - .90 .030 .035
1070 .65 - .75 .60 - .90 .030 .035
1074 .70 - .80 .50 - .80 .030 .035
1078 .72 - .85 .30 - .60 .030 .035
1080 .75 - .88 .60 - .90 .030 .035
1084 .80 - .93 .60 - .90 .030 .035
1085 .80 - .93  .70 - 1.00 .030 .035
1086 .80 - .93 .30 - .50 .030 .035
1090 .85 - .98 .69 - .90 .030 .035
1095 .90 - 1.03 .30 - .50 .030 .035
1524 .19 - .25 1.35 - 1.65 .030 .035
1527 .22 - .29 1.20 - 1.50 .030 .035
1536 .30 - .37 1.20 - 1.50 .030 .035
1541 .36 - .44 1.35 - 1.65 .030 .035
1548 .44 - .52 1.10 - 1.40 .030 .035
1552 .47 - .55 1.20 - 1.50 .030 .035